The Sensor ID Discovery Mini (also referred to as Partitalia Scanner) is a RFID reading device worn on the arm wrist. Its functionality is very similar to the xBand. It offers two buttons, one of which is freely customizable, and a vibration motor but no further sensorics.

Turning the Scanner On and Off

To turn the Scanner On press the red button (left). The LED will flash red and the scanner will vibrate once.

To turn the Scanner Off press and hold the red button until the red LED turns off.

Battery and Charging

If the battery charge gets reaches 5%, the LED will light up red. It must be charged wirelessly, e.g. by a Anker PowerWave Pad.

Pairing

Contact your Customer Success Manager to pair the reader.

Initial Config

Input...Bluetooth...Devices:
    DiscoveryMini:
        Driver: de.ubimax.android.core.util.bluetooth.handler.discovery.DiscoveryMiniGattConnectionHandler
        Name: D-mini.*
        Type: XBand
        Config:
          InitialReaderPower: 1
          InitialReaderSensitivity: 1
          InitialReaderDistance: 1
          InitialReaderTimeout: 2
          ReadAsHex: true
          ObserveBattery: true
          ObserveBatteryDelay: 60000
          Feedback: true
          RSSIFeedback: true
          ButtonCommand: INFO

Above can be seen the default config of the device. It uses its own Handler due to a custom communication protocol. Further configuration parameters are explained beneath.

Configuration Key Accepts Description

ReadAsHex

boolean

If true, the scanner excepts the content of a scanned RFID tag to be encoded in hexadecimal. The resulting scan will be decoded. If false, the scanner will produce unencoded (raw) scans.

ObserveBattery 

boolean

If ture, the scanner will periodically write the current percentage of the battery capacity in a context variable battery_status_percent under the extdevices domain (as does the xBand).

ObserveBatteryDelay 

int

Sets the delay between periodic reads of the battery capacity.

Feedback 

boolean

If true, the scanner will vibrate on every successful scan.

RSSI Feedback 

boolean

If true, every scan will contain the RSSI value (currently only logged).

InitialReaderDistance

int (0-20) 

Sets the maximal distance to accept the tag reading

InitialReaderTimeout

int (0-65535)

Sets time same tag scan gets ignored, if recognized again. 

0 - disables that functionality

1 - code will be passed, every second if in reach 

InitialReaderPower

int (0-10)

Sets the RF power emitted by the reader on initial connect.

InitialReaderSensitivity

int (0-10)

Sets the RF input gain of the reader on initial connect

Button Command

String

If  not empty, the right (blue) button will invoke the set command as an InputEvent using the device external_device

Control via workflow

Just as the xBand, the reader can be controlled via the workflow action "send_bluetooth_device_commands" (SendBluetoothDeviceCommands). Refer to the implemented commands in the following table.

Configuration Key Accepts Description

P - POWER

int (1-100)

Sets the current RF power emitted by the reader to the given percentage.

S - SENSITIVITY

int (1-100)

Sets the current RF input gain of the reader to the given percentage.

V - VIBRATION

boolean

If true, the scanner will vibrate on every successful scan.

Z - DISCONNECT

-

Disconnects the reader from the host device.

D - DISTANCE

int (1-20)

Sets the maximal distance to accept the tag reading

T - READ_TIMEOUT

int (0-65535)

Sets time after which the same tag scan gets ignored, if rescanned again.

0 - disables that functionality

1 - code will be passed, every second if in reach

F - FEEDBACK

single

 <send_external_device commands  id="send_external_device_correct">

    <commands>

        <param ="FEEDBACK">single</paran>

    </commands>

</send_external_device_commands>

F - FEEDBACK

triple

 <send_external device commands  id="send_external_device_negative">

    <commands>

        <param ="FEEDBACK">trible</paran>

    </commands>

</send_external_device_commands>

Example

<actions>
    <send_external_device_commands id="send_external_device_power">
            <commands>
                <param name="P">80</param>
            </commands>
    </send_external_device_commands>
</actions>